- Saga cutting plotter driver download how to#
- Saga cutting plotter driver download manual#
- Saga cutting plotter driver download software#
The blade should not cut through the substrate as it will damage your Teflon cutting strip.
When the cutter is setup for cutting you will need to adjust the cutting force so that the blade fully cuts through the vinyl layer and partially cuts through the substrate (or carrier or release liner). We recommend starting with an exposure distance of about 1/32 (approximately the thickness of a credit card). As such, the blade doesn t need to be exposed from the blade holder shield very much. Sign vinyl is only thick which only uses a very small amount of the blade (only the very tip is used in cutting thin materials). step1 step2 step3 The correct blade depth It is important for good quality vinyl cutting to achieve the correct blade depth of cut. Press the push-pin to remove the blade form the blade holder when replacing blade. Adjust the blade tip to suitable length by unlocking (rotate counter clockwise) the lock nut and rotating the blade holder shield and relocking the lock nut. Roll holder support Floor stand Roll holder support 4ħ 2. T-stand for left side stand beam T-stand for right side Step3 Position the roll holder support s to floor stand as shown below, and tighten screws. Repeat the same steps with any additional stand beams. Tighten them to form a left T-stand.Repeat the same steps with the support for the right side Support the left side screw Screw Bottom stand 3Ĥ Step2 Place the stand beam upright on the T-stand and put the screws into the holes, but don t tighten them at this step. 1 Spanner, 1 hex key 3.Floor Stand Installation Step1 Position the support for the left side perpendicularly to the bottom stand and place the screws into the holes.
Saga cutting plotter driver download software#
2.What s in the box Please check immediately to ensure that you have received the following articles: Cutting plotter Cutting plotter stand (dismantled and in the bottom of the box) Power cord USB connection Lead RS-232 connection Lead Blade holder Pen holder and pen Safety fuse (spare) 3 Drag knife blades CD with software and drivers. Manually moving the carriage can induce currents from the motor into the motherboard, overload the electronics and damage the machine. Do not use your hands to manually move the carriage, use the control buttons in off-line mode instead. During severe weather, unplug the machine. 2ģ Never run the machine during a thunder storm as lighting could damage or destroy the machine. Set up the machine on a stable base to avoid danger of falling. Do not touch the tips of the cutting blade to avoid injury and damage to the blade tip. Keep the cutting plotter away from children, and never leave the machine or machine parts unattended when plugged-in. Keep your hands well away from the blade holder while the carriage is running! Cancel the active job or preferably, power down the cutter before adjusting the blade holder. Unplug the power lead during long periods of inactivity. In case of extreme main power fluctuations, use a voltage stabilizer. Insure that the main power supply(220v/110v) doesn t fluctuate by more than ☑0%. Your stand should be electrically connected to the vinyl cutter. Grounding is very important for proper cutter function.
Do not bypass the ground lead for the cutter. Avoid liquid spills and metal objects from entering the interior of the cutter. Never open the machine case and don t attempt to modify the machine without instructed to do so by a Saga technician. Keep your hands or other parts of the body far from the carriage when using the machine. Release the pressure contact rollers when not in use by flipping the pressure levers up on the back side of the cutter. Don t unplug the connection to the computer lead line when the plotter is running as this may cause damage to plotter. Don t place magnetic objects near the cutting head as it will affect cutting pressure and possibly damage the carriage mechanism. Precautions: Please read these instructions and precautionary notes carefully before using the machine for the first time. We do not assume any liability for direct or indirect damage that occurs due to the use of this product.
Saga cutting plotter driver download how to#
It tells you how to prepare your cutting plotter for production use in a few easy steps.
Saga cutting plotter driver download manual#
For all comments, queries or suggestions concerning this manual please contact us. 1 SAGA-420I SAGA-720I/IP SAGA-1350I/IP SAGA-420II/IIP SAGA-720II/IIP SAGA-1350II/IIP SAGA-1750II/IIP 1Ģ Congratulations on purchasing a Saga cutting plotter! NOTICE: We reserve the right to modify the information contained in this user manual at any time without prior notice un-authorized modification, copying or distribution is prohibited.